E-Genius Appliance Repair EPA Universal CertifiedEPA Certified $2M Insured Registered Charlotte, NC BusinessRegistered in Charlotte, NC

Amana
Washer Repair

Experienced technicians serving your neighborhood.

Amana Washer Repair in 3 Steps

Need Amana washer repair in Charlotte, NC? Tell us about not draining or water leaks and choose a service visit.

  1. Describe Your Washer Issue

    Report not draining, water leaks, or an error message if shown. Include the Amana washing machine model number.

  2. Schedule Washer Service

    Choose an available time for your Amana washer repair appointment in Charlotte.

  3. Review Repair Options

    Our technician checks drainage, spin, and water-supply problems on your Amana washing machine, as applicable, and explains the repair estimate.

Book Amana Washer Repair

Quick, convenient online scheduling · Opens in a new tab.

Amana Washer Repair in Charlotte, NC

E-genius Appliance Repair provides Amana washer repair in Charlotte, NC for common problems such as drainage problems, spin-cycle issues, leaks, vibration, unusual noises, or a washer that will not start. Our technicians diagnose the issue, explain the recommended repair, and service compatible Amana equipment and models.

Schedule online or call (980) 443-5851 to request washer repair.

Open & Available: (980) 443-5851 (980) 443-5851

Easy booking

We're only a few clicks or a phone call away.

In-home estimate

No risk. No pressure.

E-genius Appliance Repair Guarantee

Guaranteed parts and service.

Quality results

Expert technicians.

Amana washer troubleshooting

Common Amana Washer Problems

If your Amana washer will not start, fill, drain, or spin, begin with the symptom that best describes the cycle. Front-load and top-load machines use different controls; the notes below help separate routine settings from conditions that need diagnosis.

These are possible service scenarios, not confirmed diagnoses or a ranking of defect frequency. Use only the checks permitted by your model's owner manual.

Power & Starting10 issues
  • Washer Won't Turn On

    Possible causes or conditions: Supply, outlet, cord or control may be involved; verify installation and recorded code.

    Applies to: All washer controls

    Next step: Check household supply and documented restart procedure; recurring electrical faults need qualified service.

  • No Display

    Possible causes or conditions: Loss of supply or display/control problem are possible; confirm whether any indicators work.

    Applies to: Electronic display models

    Next step: Check household supply and documented restart procedure; recurring electrical faults need qualified service.

  • Turns off during cycle

    Possible causes or conditions: Distinguish supply interruption from a programmed pause; record when it stops.

    Applies to: All washer controls

    Next step: Check household supply and documented restart procedure; recurring electrical faults need qualified service.

  • Trips the breaker

    Possible causes or conditions: Electrical fault or circuit problem needs qualified diagnosis; stop repeated resets.

    Applies to: All washer controls

    Next step: Stop using the washer and do not keep restarting it or resetting the breaker. Keep clear of wet electrical parts; arrange qualified appliance or electrical diagnosis. For active fire, smoke, or immediate danger, leave the area and call 911.

  • Washer Won't Start

    Possible causes or conditions: Check selected cycle, start procedure, control lock, delay start and closure status.

    Applies to: All washer controls

    Next step: Record the exact display and model; qualified service should test the affected circuit.

  • Start button does not respond

    Possible causes or conditions: Control lock, button state or UI issue may be involved; do not assume main-board failure.

    Applies to: Electronic controls

    Next step: Record the exact display and model; qualified service should test the affected circuit.

  • Buttons do not work

    Possible causes or conditions: Confirm lock mode and wet/dirty control surface before service diagnosis.

    Applies to: Electronic controls

    Next step: Record the exact display and model; qualified service should test the affected circuit.

  • Beeps but will not run

    Possible causes or conditions: Record the beep pattern and illuminated indicators; alerts can be status or faults.

    Applies to: Audible-alert controls

    Next step: Record the exact display and model; qualified service should test the affected circuit.

  • Burning Smell

    Possible causes or conditions: Stop use, isolate power when safely accessible and arrange qualified diagnosis.

    Applies to: All washers

    Next step: Stop using the washer and do not keep restarting it or resetting the breaker. Keep clear of wet electrical parts; arrange qualified appliance or electrical diagnosis. For active fire, smoke, or immediate danger, leave the area and call 911.

  • Sparks or electric shock

    Possible causes or conditions: Stop use and arrange qualified electrical / appliance service.

    Applies to: All washers

    Next step: Stop using the washer and do not keep restarting it or resetting the breaker. Keep clear of wet electrical parts; arrange qualified appliance or electrical diagnosis. For active fire, smoke, or immediate danger, leave the area and call 911.

Filling & Water Level9 issues
  • Washer Not Filling with Water

    Possible causes or conditions: Faucet, supply hose, inlet screen, valve or sensing problem is possible.

    Applies to: All washers

    Next step: Check open supply faucets and visible hose restrictions; persistent fault requires model-specific diagnosis.

  • Fills very slowly

    Possible causes or conditions: Low supply pressure or restrictions may be involved; check visible hoses.

    Applies to: All washers

    Next step: Check open supply faucets and visible hose restrictions; persistent fault requires model-specific diagnosis.

  • No hot water

    Possible causes or conditions: Check household hot supply and hose routing; internal heater is a separate feature.

    Applies to: Separate hot/cold inlet models

    Next step: Check open supply faucets and visible hose restrictions; persistent fault requires model-specific diagnosis.

  • No cold water

    Possible causes or conditions: Check household cold supply, faucet and hose routing.

    Applies to: Separate hot/cold inlet models

    Next step: Check open supply faucets and visible hose restrictions; persistent fault requires model-specific diagnosis.

  • Water temperature is wrong

    Possible causes or conditions: Hose reversal, supply temperature and cycle design may affect results.

    Applies to: Temperature-selection models

    Next step: Check open supply faucets and visible hose restrictions; persistent fault requires model-specific diagnosis.

  • Fills and drains at the same time

    Possible causes or conditions: Drain siphoning / installation and level sensing are possible; verify drain setup.

    Applies to: All washers

    Next step: Compare the drain-hose installation with the model manual without changing internal parts. If siphoning or repeated filling continues, arrange diagnosis of the installation and level system.

  • Keeps filling

    Possible causes or conditions: Inlet or level control may be involved; close water supply and stop use.

    Applies to: All washers

    Next step: Stop use and close the water supply; arrange service for internal leakage.

  • Cannot see water in the drum

    Possible causes or conditions: Low visible water may be normal; compare with actual fill faults and wash results.

    Applies to: HE front-load models only

    Next step: Check the owner manual for this control; this message alone does not establish a failed part.

  • Low water level

    Possible causes or conditions: Low level can be normal; verify model behavior before a fill-fault diagnosis.

    Applies to: Automatic-level HE top-load models

    Next step: Check the owner manual for this control; this message alone does not establish a failed part.

Drainage6 issues
  • Washer Not Draining

    Possible causes or conditions: Drain restriction, pump, installation or foam are possibilities.

    Applies to: All washers

    Next step: Check the visible drain hose and household drain; use only model-approved accessible filter instructions. Service if persistent.

  • Drains slowly

    Possible causes or conditions: Check visible drain restrictions and household drain; internal inspection needs model procedure.

    Applies to: All washers

    Next step: Check the visible drain hose and household drain; use only model-approved accessible filter instructions. Service if persistent.

  • Water left in tub

    Possible causes or conditions: Check whether the cycle ended normally; distinguish sump residue from retained tub water.

    Applies to: All washers

    Next step: Check the visible drain hose and household drain; use only model-approved accessible filter instructions. Service if persistent.

  • Drain pump keeps running

    Possible causes or conditions: Flood protection, retained water or control issue may be involved; record codes.

    Applies to: All washers

    Next step: Check the visible drain hose and household drain; use only model-approved accessible filter instructions. Service if persistent.

  • Drain pump hums

    Possible causes or conditions: A hum alone cannot distinguish blockage from electrical or pump faults.

    Applies to: All washers

    Next step: Check the visible drain hose and household drain; use only model-approved accessible filter instructions. Service if persistent.

  • Overflows the standpipe

    Possible causes or conditions: Household drain capacity / restriction or installation may be involved.

    Applies to: All washers

    Next step: Stop the cycle and prevent further water discharge if safe. Have the household drain and installation checked; a household plumbing blockage is not automatically a failed washer pump.

Spin, Noise & Vibration14 issues
  • Washer Not Spinning

    Possible causes or conditions: Drain, load distribution, spin selection, closure or drive may be involved.

    Applies to: All washers

    Next step: Redistribute the load and check leveling; repeated failure with normal loads needs service.

  • Clothes Still Wet After the Cycle

    Possible causes or conditions: Review spin setting, load balance and draining before assuming a drive failure.

    Applies to: All washers

    Next step: Redistribute the load and check leveling; repeated failure with normal loads needs service.

  • Spin cycle stops

    Possible causes or conditions: Balance protection, closure, draining or drive issues are possible.

    Applies to: All washers

    Next step: Redistribute the load and check leveling; repeated failure with normal loads needs service.

  • Will not reach high spin speed

    Possible causes or conditions: Selected speed, load balance, foam or drive may limit spin.

    Applies to: Variable-spin models

    Next step: Redistribute the load and check leveling; repeated failure with normal loads needs service.

  • Shaking During Spin

    Possible causes or conditions: Check leveling, load distribution and installation before component diagnosis.

    Applies to: All washers

    Next step: Redistribute the load and check leveling; repeated failure with normal loads needs service.

  • Walks across the floor

    Possible causes or conditions: Floor support, feet, load and installation should be assessed.

    Applies to: All washers

    Next step: Redistribute the load and check leveling; repeated failure with normal loads needs service.

  • Bangs during spin

    Possible causes or conditions: Unbalanced load, installation or suspension problems are possible.

    Applies to: All washers

    Next step: Redistribute the load and check leveling; repeated failure with normal loads needs service.

  • Grinding Noise

    Possible causes or conditions: Foreign objects, pump or drive may be involved; record the cycle stage.

    Applies to: All washers

    Next step: Stop the cycle; persistent drive faults require service and component testing.

  • Squealing noise

    Possible causes or conditions: Noise origin needs inspection; symptom does not prove belt or bearing failure.

    Applies to: All washers

    Next step: Stop the cycle; persistent drive faults require service and component testing.

  • Rattling noise

    Possible causes or conditions: Check external contact and items in the load; internal noise needs inspection.

    Applies to: All washers

    Next step: Stop the cycle; persistent drive faults require service and component testing.

  • Will not tumble

    Possible causes or conditions: Drive, closure or control may be involved; distinguish tumble from high-speed spin.

    Applies to: Front-load models only

    Next step: Stop the cycle; persistent drive faults require service and component testing.

  • Vibrates after installation

    Possible causes or conditions: Transport restraints, leveling and floor support need verification.

    Applies to: Front-load models only

    Next step: Redistribute the load and check leveling; repeated failure with normal loads needs service.

  • Will not agitate

    Possible causes or conditions: Drive, cycle stage, lid control or obstruction may be involved.

    Applies to: Top-load agitator / impeller models only

    Next step: Stop the cycle; persistent drive faults require service and component testing.

  • Agitator barely moves

    Possible causes or conditions: Check cycle behavior and load; worn drive parts require inspection.

    Applies to: Top-load agitator models only

    Next step: Stop the cycle; persistent drive faults require service and component testing.

Doors & Locks5 issues
  • Clicking noise

    Possible causes or conditions: Some relay / lock clicks are normal; correlate with failure to start or lock.

    Applies to: Interlocked electronic models

    Next step: Remove trapped laundry and close normally; do not bypass or force the interlock.

  • Control lock will not turn off

    Possible causes or conditions: Use the exact model button sequence; do not assume latch failure.

    Applies to: Control-lock equipped models

    Next step: Check the owner manual for this control; this message alone does not establish a failed part.

  • Door or Lid Won't Unlock

    Possible causes or conditions: Retained water, hot water, motion or lock fault may prevent release; never force open.

    Applies to: Interlock-equipped models

    Next step: Do not force the lock or reach into a moving washer. Retained water, heat, or motion may delay release; follow only the model-approved procedure and request service if it remains locked.

  • Door or lid will not lock

    Possible causes or conditions: Check closure and trapped clothing; switch / latch circuit requires testing.

    Applies to: Interlock-equipped models

    Next step: Remove trapped laundry and close normally; do not bypass or force the interlock.

  • Lid locked and will not start

    Possible causes or conditions: Check codes and water/motion state; never bypass lid protection.

    Applies to: Lid-lock equipped top-load models

    Next step: Remove trapped laundry and close normally; do not bypass or force the interlock.

Leaks & Seals6 issues
  • Fills when turned off

    Possible causes or conditions: Inlet leakage or drain backflow may be involved; close water supply and arrange diagnosis.

    Applies to: All washers

    Next step: Stop use and close the water supply; arrange service for internal leakage.

  • Water Leaking Underneath

    Possible causes or conditions: Supply, drain, tub, dispenser or internal connections are possible; locate source.

    Applies to: All washers

    Next step: Stop use and close the water supply; arrange service for internal leakage.

  • Leaks from the back

    Possible causes or conditions: Inspect visible supply / drain connections without opening the cabinet.

    Applies to: All washers

    Next step: Stop use and close the water supply; arrange service for internal leakage.

  • Leaks during fill

    Possible causes or conditions: Supply, inlet path or dispenser may be involved; note first wet location.

    Applies to: All washers

    Next step: Stop use and close the water supply; arrange service for internal leakage.

  • Leaks during drain

    Possible causes or conditions: Drain hose, household drain or pump path may be involved.

    Applies to: All washers

    Next step: Stop use and close the water supply; arrange service for internal leakage.

  • Leaks from the door

    Possible causes or conditions: Trapped fabric, residue, gasket damage or closure may be involved.

    Applies to: Front-load models only

    Next step: Stop use and close the water supply; arrange service for internal leakage.

Cycles & Controls7 issues
  • Flashing lights

    Possible causes or conditions: Obtain a panel photo and count flashes; patterns differ by model.

    Applies to: LED control models

    Next step: Record the exact display and model; qualified service should test the affected circuit.

  • Stuck on sensing

    Possible causes or conditions: Load sensing, supply, closure or drive problems are possibilities; record elapsed time.

    Applies to: Automatic load-sensing controls

    Next step: Record the exact display and model; qualified service should test the affected circuit.

  • Washer Stops Mid-Cycle

    Possible causes or conditions: Record the cycle stage, water left inside and any display message.

    Applies to: All washers

    Next step: Record the exact display and model; qualified service should test the affected circuit.

  • Takes too long

    Possible causes or conditions: Load, selected options, cold supply, foam and balancing can extend time.

    Applies to: All washers

    Next step: Record the exact display and model; qualified service should test the affected circuit.

  • Timer stuck at one minute

    Possible causes or conditions: Displayed time is an estimate; draining or balancing may delay completion.

    Applies to: Electronic time display models

    Next step: Record the exact display and model; qualified service should test the affected circuit.

  • Keeps restarting the cycle

    Possible causes or conditions: Distinguish balancing retries from power resets; note display behavior.

    Applies to: Electronic controls

    Next step: Record the exact display and model; qualified service should test the affected circuit.

  • Load size light flashing

    Possible causes or conditions: Model-specific pattern; do not interpret from a different manufacturer.

    Applies to: Top-load controls with load-size indicators

    Next step: Record the exact display and model; qualified service should test the affected circuit.

Detergent, Cleaning & Care14 issues
  • Too much foam

    Possible causes or conditions: Detergent formulation and dose, water conditions and load can contribute.

    Applies to: All washers

    Next step: Review detergent type and dose against the owner manual; reduce oversudsing.

  • Soap left on clothes

    Possible causes or conditions: Review dose, loading and rinse selections; not proof of a failed rinse system.

    Applies to: All washers

    Next step: Review detergent type and dose against the owner manual; reduce oversudsing.

  • Does not rinse properly

    Possible causes or conditions: Fill, loading, detergent and selected settings need review.

    Applies to: All washers

    Next step: Review detergent type and dose against the owner manual; reduce oversudsing.

  • Clothes still dirty

    Possible causes or conditions: Cycle, loading, detergent and movement issues are possible.

    Applies to: All washers

    Next step: Follow the model owner manual maintenance procedure.

  • Unpleasant Odor

    Possible causes or conditions: Moisture, residue or plumbing may contribute; identify where odor originates.

    Applies to: All washers

    Next step: Follow the model owner manual maintenance procedure.

  • Black flakes on clothes

    Possible causes or conditions: Residue or external contamination is possible; inspect before naming a failed part.

    Applies to: All washers

    Next step: Follow the model owner manual maintenance procedure.

  • White residue on clothes

    Possible causes or conditions: Dose, dissolving, loading and water conditions need review.

    Applies to: All washers

    Next step: Follow the model owner manual maintenance procedure.

  • Rust stains on clothes

    Possible causes or conditions: Check water supply and metal items; not proof of tub corrosion.

    Applies to: All washers

    Next step: Follow the model owner manual maintenance procedure.

  • Damages clothes

    Possible causes or conditions: Check load items, care labels and visible drum damage; stop if snagging persists.

    Applies to: All washers

    Next step: Follow the model owner manual maintenance procedure.

  • Detergent not dispensing

    Possible causes or conditions: Drawer blockage, setup, routing or metering may be involved.

    Applies to: Dispenser-equipped models

    Next step: Check drawer seating and model-approved cleaning / refill steps; persistent faults need service.

  • Fabric softener not dispensing

    Possible causes or conditions: Check approved fill limit and model-specific dispenser cleaning.

    Applies to: Softener-dispenser models

    Next step: Check drawer seating and model-approved cleaning / refill steps; persistent faults need service.

  • Dispenser holds water

    Possible causes or conditions: Small residual amount can be normal; excess may need cleaning / diagnosis.

    Applies to: Drawer-dispenser models

    Next step: Check drawer seating and model-approved cleaning / refill steps; persistent faults need service.

  • Door gasket smells

    Possible causes or conditions: Moisture / residue can contribute; use approved cleaning procedure.

    Applies to: Front-load models only

    Next step: Follow the model owner manual maintenance procedure.

  • Mold on the door seal

    Possible causes or conditions: Inspect and clean per manual; visible growth does not establish an internal part failure.

    Applies to: Front-load models only

    Next step: Follow the model owner manual maintenance procedure.

Temperature & Equipped Features1 issues
  • Door glass gets hot

    Possible causes or conditions: Incoming hot water or equipped heating may warm the glass; abnormal overheating needs service.

    Applies to: Hot-wash front-load cycle; internal heater not assumed

    Next step: Stop use if abnormal heating occurs; temperature / heater faults require service.

Do not open the cabinet, bypass a lock, or probe electrical components. Internal repairs require qualified diagnosis; leaking or unsafe equipment should not be run repeatedly.

Repair options after diagnosis

Amana Washer Repairs and Parts Replacement

The work needed depends on your Amana model and the cause of the problem. These are repair options we can assess, not a diagnosis from a symptom or error code alone. Model compatibility and parts availability must be confirmed.

Drain Pump and Drainage Repairs

Water left in an Amana tub can involve the drain route, pump, foam, or installation. We assess the drainage problem before recommending a pump or another replacement part.

Water Inlet and Level-Control Repairs

Slow filling, no water, and continued filling need different checks. Amana inlet valves and level controls should be assessed against the supply conditions and the exact model.

Door and Lid-Lock Repairs

A front-load door lock and a top-load lid lock are not interchangeable systems. We review closure, lock feedback, and the Amana control before recommending a repair.

Spin and Drive-System Repairs

Poor spin or a stalled wash action may involve drainage, the load, or the drive. We check the Amana design rather than assume every washer needs a belt.

Leak and Seal Repairs

The first wet area helps narrow an Amana leak to a hose, dispenser, connection, or seal. Front-load door-gasket work applies only to the appropriate models.

Control, Sensor and Dispenser Repairs

Unresponsive controls or a dispensing fault need model-specific diagnosis. Cartridge-related work is considered only on Amana washers equipped with that removable dispenser.

Not sure which repair your Amana washer needs? Include the full model number and describe what happens during the cycle. Our team will review the request and confirm service availability.

Request Amana Washer Service
Codes, indicators & messages

Amana Washer Error Codes & Messages

Amana front-load and HE top-load controls do not share one universal code list. Select the documented family, compare the exact display, and check the model notes before using a meaning.

This reference covers the Amana support families listed in the source file, including selected legacy front-load codes. A removable detergent cartridge is relevant only when that feature is fitted.

Service-reference entries may require technician diagnostics and may never appear on the normal display. No service-mode entry or component-testing instructions are provided here. Combo drying entries apply only to that subsystem.

F5E2Fault

Door lock failure

Also shown as: F5 E2

Applies to: US front-load support families

Next step: Remove trapped laundry and close normally; do not bypass or force the interlock.

Source and model reference
F7E1Fault

Motor-speed sensing fault

Also shown as: F7 E1

Applies to: US front-load support families

Next step: Stop the cycle; persistent drive faults require service and component testing.

Source and model reference
F8E1Fault

Low water flow

Also shown as: F8 E1; LOFL

Applies to: US front-load support families

Next step: Check open supply faucets and visible hose restrictions; persistent fault requires model-specific diagnosis.

Source and model reference
F8E2Fault

Dispenser system fault

Also shown as: F8 E2

Applies to: US front-load support families

Next step: Check drawer seating and model-approved cleaning / refill steps; persistent faults need service.

Source and model reference
F9E1Fault

Long drain

Also shown as: F9 E1

Applies to: US front-load support families

Next step: Check the visible drain hose and household drain; use only model-approved accessible filter instructions. Service if persistent.

Source and model reference
SudFault

Excessive foam

Also shown as: Sd

Applies to: US front-load support families

Next step: Review detergent type and dose against the owner manual; reduce oversudsing.

Source and model reference
rLFault

Load during Clean Washer

Also shown as: F34

Applies to: US front-load support families

Next step: Follow the model owner manual maintenance procedure.

Source and model reference
dETFault

Dispenser cartridge absent

Applies to: US front-load support families

Model note: Only models with removable detergent cartridge.

Next step: Check drawer seating and model-approved cleaning / refill steps; persistent faults need service.

Source and model reference
LOCStatus

Control lock active

Also shown as: LC

Applies to: US front-load controls

Next step: Check the owner manual for this control; this message alone does not establish a failed part.

Source and model reference
IntStatus

Cycle interrupted / canceled

Applies to: US front-load controls

Next step: Check the owner manual for this control; this message alone does not establish a failed part.

Source and model reference
drnFault

Drain problem

Applies to: US HE top-load support families

Next step: Check the visible drain hose and household drain; use only model-approved accessible filter instructions. Service if persistent.

Source and model reference
HCFault

Hot / cold hoses reversed

Applies to: US HE top-load support families

Next step: Check open supply faucets and visible hose restrictions; persistent fault requires model-specific diagnosis.

Source and model reference
LdLFault

Lid cannot lock

Applies to: US HE top-load support families

Next step: Remove trapped laundry and close normally; do not bypass or force the interlock.

Source and model reference
LdUFault

Lid cannot unlock

Applies to: US HE top-load support families

Next step: Remove trapped laundry and close normally; do not bypass or force the interlock.

Source and model reference
LFFault

Long fill

Also shown as: Lo FL; F8E1

Applies to: US HE top-load support families

Next step: Check open supply faucets and visible hose restrictions; persistent fault requires model-specific diagnosis.

Source and model reference
lidFault

Lid open

Applies to: US HE top-load support families

Next step: Remove trapped laundry and close normally; do not bypass or force the interlock.

Source and model reference
OfbFault

Off-balance load

Applies to: US HE top-load support families

Next step: Redistribute the load and check leveling; repeated failure with normal loads needs service.

Source and model reference
OLFault

Overload

Applies to: US HE top-load support families

Next step: Redistribute the load and check leveling; repeated failure with normal loads needs service.

Source and model reference
PFFault

Power interruption

Applies to: US HE top-load support families

Next step: Check household supply and documented restart procedure; recurring electrical faults need qualified service.

Source and model reference
SudFault

Excessive foam

Applies to: US HE top-load support families

Next step: Review detergent type and dose against the owner manual; reduce oversudsing.

Source and model reference
F20Fault

Fill problem

Also shown as: FH

Applies to: Legacy US front-load displaying F20 / FH

Next step: Check open supply faucets and visible hose restrictions; persistent fault requires model-specific diagnosis.

Source and model reference
F21Fault

Long drain

Also shown as: F02

Applies to: Legacy US front-load displaying F21 / F02

Next step: Check the visible drain hose and household drain; use only model-approved accessible filter instructions. Service if persistent.

Source and model reference
F0E2Fault

Excessive foam

Also shown as: F0 E2

Applies to: US top-load displaying F0E2

Next step: Review detergent type and dose against the owner manual; reduce oversudsing.

Source and model reference

Model check first: the same code may have more than one meaning across control families. Normal lock, cleaning, update, or cooldown messages are not automatically faults. Do not order parts from a code alone.

Professional service

When to Schedule Amana Washer Repair

An Amana washer that repeatedly fails under normal operating conditions needs more than another restart. Send the model number, the stage where it stops, and any displayed code so we can review the service request.

  • The same problem returns after safe owner-manual checks.
  • A normal load repeatedly fails to complete the cycle.
  • Water remains in the tub or the machine cannot drain normally.
  • Leakage continues or a protection warning requires service.
  • The door or lid stays locked after the documented release conditions.
  • The model reference calls for internal electrical or component testing.

Amana Washer Repair? Read Our Reviews

Looking into Amana washer repair in Charlotte? Whether it is drainage issues or water leaks, see what customers say on Google about their experience with E-genius Appliance Repair before making an appointment.

5.0 200+ Google reviews READ ALL GOOGLE REVIEWS

Already our customer?

Did E-genius Appliance Repair work on your Amana washer? We'd be grateful for your thoughts on Google. Reviews help us improve and support informed decisions in Charlotte.

Leave a Google review
Illustration of an E-genius Appliance Repair technician and a homeowner in a kitchen

Thank you for your support!

Washer repair in Charlotte, NC

Amana Washer Repair

Is your Amana washer not draining, filling slowly, or stopping before the spin cycle? Share the model and symptoms to discuss repair service in Charlotte.

  • Drain, fill and spin problems
  • Review diagnosis and repair options
Illustrative washing machine in a home laundry area for Amana washer repair

Request a Call Back

Leave your number. We'll call you about your Amana washer.

Your details are used to respond to your callback request.

Have questions? We have answers.

Frequently Asked Questions About Amana Washer Repair

What does “rL” mean on my Amana washer?

For U.S. front-load support families, “rL” indicates load during Clean Washer. Follow the exact model’s approved care and acknowledgment procedure. Record the current indication if it remains after the required maintenance is completed.

What does “LOC” indicate on my Amana washer?

For U.S. front-load controls, “LOC” indicates control lock active. Use the exact owner guide to change the lock setting. Record any message and seek service if normal control operation does not return afterward.

Why are clothes still soaking wet after my Amana washer finishes?

Check the chosen spin speed, load distribution, and whether the tub drained. Record excess foam or repeated balancing attempts. If a correctly loaded cycle still ends with wet laundry, the drain, sensing, and drive functions may need assessment.

What should I check if my Amana washer will not drain?

Record the code, water level, and cycle stage. Follow the exact owner instructions for any accessible drain filter and visible hose checks, allowing for hot water. Avoid forcing the door or removing panels; recurring retained water needs service.

Other Amana Products We Service

Need service for another Amana product? Beyond washer, E-genius Appliance Repair supports the additional Amana categories below. Select the closest match, or send us a request so we can review your equipment.

(980) 443-5851 call me back